Friday, April 26, 2013

Project: Static Route Configuration



For this project on Static Configuration we had to build a topology that included 4 2911 Routers, and 4 2960 Switches. The routers in the topology had to WIC 2T cards in order to be connected to each other with DCE and DTE Serial Wires. The switches were to be connected with straight through wires to the GigaEthernet ports of the Routers. The PCs were connected to the Fast Ethernet Ports of the Switches. The problem I had was that When connecting the topology I had forgotten to turn off the router to install the WIC 2T cards. At one point I also forgot to install the WIC 2T cards. When placing the ip addresses on the network You have to make sure it goes in the correct port interface. After you have completed the Basic Configuration of all routers, You Statically Configure all of the networks. Below is the procedure I did to Statically configure all the routers. When Finished ping all routes to ensure that the topology is working.
Static Configuration :

1.Go to router 1,  and configure it :
            - Router>ena
            -Router#config
            - Router(config)# hostname Border
            - Border(config)# ena password Cisco
            - Border(config) # ena secret Class
            -Border(config)#banner motd * This mine Get out, for assistance contact Brianna Price 347-568-5698*
             -Border(config)# ctrlz
             -Border# copy running-config startup-config
             - Border# config
             - Border(config)# int s0/3/0
             -Border(config-if)# ip address 1.1.1.2 255.255.255.252
              -Border(config-if)# ctrlz
              -Border#config
               - Border(config)#int loopback0
              -Border(config-if)# ip address 198.155.202.1 255.255.255.255
               -Border(config-if)# ctrlz
               -Border#config
               -Border(config)# ip route 1.1.1.4 255.255.255.252 s0/3/0
               -Border(config)#ip route 1.1.1.8 255.255.255.252 s0/3/0
               -Border(config)# ip route 192.168.10.0 255.255.255.224 s0/3/0
               -Border(config)#ip route 192.168.20.0 255.255.255.224 s0/3/0
                -Border(config)#ip route 192.168.30.0 255.255.255.224  s0/3/0
               -Border(config)# ip route 192.168.40.0 255.255.255.224 s0/3/0
               -Border(config)# ctrlz
               -Border# copy running-config startup-config
4. Go to router 2 and configure it:
              -Router>ena
              -Router#config
              -Router(config)# hostname NewYork
              -NewYork(config)# ena password Cisco
              -NewYork(config)# ena secret Class
              -NewYork(config)#banner motd *This is mine get out, For assistance contact Brianna Price 347-568-5698*
               - NewYork(config)#ctrlz
                -NewYork#copy running-config startup-config
               -NewYork#config
               -NewYork(config)# int s0/2/0
               -NewYork(config-if)# ip address 1.1.1.1 255.255.255.252
               -NewYork(config-if)# ctrlz
               -NewYork#config
               -NewYork(config)# int s 0/3/0
               -NewYork(config-if)# ip address 1.1.1.10 255.255.255.255.252
              -NewYork(config-if)# ctrlz
               -NewYork(config)# int s0/3/1
                -NewYork(config-if)# ip address 1.1.1.6 255.255.255.252
                 -NewYork(config-if)#ctrlz
             -New York#config
             -NewYork(config)# ip route 192.168.10.0 255.255.255.0 s/0/3/1
            -NewYork(config)# no shutdown
           --NewYork(config)# ctrlz
           -NewYork(config)# ip route 192.168.20.0 255.255.255.0 s/0/3/1
           -NewYork(config)# ctrlz
           -NewYork(config)# ip route 192.168.168.40.0 255.255.255.0 s0/3/1
          -NewYork(config)# ctrlz
          -NewYork(config)# ip route 192.168.30.0 255.255.255.0 s0/3/1
          - New York(config)# ctrlz
         --NewYork#copy running-config startup-config
5. Go to router 3 and configure it:
         -Router>ena
         -Router#config
        -Router(config)# hostname Vegas
       -Vegas(config)# ena password Cisco
       -Vegas(config)# ena secret Class
       -Vegas(config)#banner motd *This is mine get out, For assistance please contact Brianna Price 347-568-5698*
        -Vegas(config)#ctrlz
       -Vegas#copy running-config startup-config
       -Vegas#config
       -Vegas(config)# int s0/2/0
      -Vegas(config-if)# ip address 1.1.1.9 255.255.255.252
      -Vegas(config-if)# ctrlz
     -Vegas#config
     -Vegas(config)# int g0/0
     -Vegas(config-if)# ip address 192.168.40.254 255.255.255.224
     -Vegas(config-if)# ctrlz
     -Vegas#config
    -Vegas(config)# int g0/1
    -Vegas(config)# ip address 192.168.30.254 255.255.255.224
    -Vegas(config-if)# ctrlz
    -Vegas#config
    -Vegas(config)#ip route 1.1.1.0 255.255.255.252 s0/2/0
     -Vegas(config)# ctrlz
 -Vegas(config)#ip route 1.1.1.4 255.255.255.252 s0/2/0
  -Vegas(config)#ctrlz
 -Vegas(config)#ip route 192.168.10.0 255.255.255.0 s0/2/0
  Vegas(config)# ctrlz
  -Vegas(config)#ip route 192.168.20.0 255.255.255.0 s0/2/0
   -Vegas(config)#ctrl z
   Vegas#copy running-config startup-config
6. Go to router 4 and configure it:
   -Router>ena
   -Router#config
    -Router(config)# hostname Boston
   -Boston(config)#ena password Cisco
Boston(config)# ena secret Class
Boston(config)#banner motd *this is mine get out For assistance contact Brianna Price 347-568-5698*
Boston(config)#ctrlz
Boston#copy running-config startup-config
Boston# config
Boston(config)#int s0/3/0
Boston(config-if)# ip address 1.1.1.5 255.255.255.252
Boston(config-if)#no shutdown
Boston#config
Boston(config)# int g0/0
Boston(config-if)# ip address 192.168.20.254 255.255.255.0
Boston(config-if)#ctrlz
Boston#config
 Boston(config)# int g0/1
Boston(config-if)# ip address 192.168.10.254 255.255.255.0
Boston(config-if)#ctrlz
SInce you have Labeled and assigned ip addresses to the interface of the Last Router, You have to make it so that Boston knows about the other Subnetworks on the Entire Network. SO you must Statically Configure Boston.

Once this is finished you will have Statically configured the entire Network :)


 

No comments:

Post a Comment